![]()
![]()
The combination guy hook / pole eye attachment consolidates two pole line functions into a single ductile iron casting: an open hook for seating a guy strand, thimble, or clevis, and an integral eye (or eye plate) for a second connection point. In a standard guying system this means one fitting, one bolt set, and one installation step instead of separate guy hook and eye plate hardware mounted individually on the pole. For utilities and line builders, the combination design reduces the parts count on the truck, shortens climb time, and guarantees that the two connection points are permanently aligned relative to each other by the casting itself.
The fitting serves distribution poles carrying mixed attachments—for example a down guy terminating in the hook while a span guy or auxiliary lead hangs from the eye. Cast in ductile iron per ASTM A536 (typically Grade 65-45-12 or EN-GJS-450-10), the body provides the strength and shock resistance that load-bearing pole hardware requires, and the hot-dip galvanized finish per ASTM A153 protects it for decades of outdoor exposure. A variant with a lower bolt hole sized for a clevis connection is available for crews who need to hang a clevis-ended assembly below the main attachment; both versions share the same body concept and load class.
| Parameter | Typical Value |
|---|---|
| Material | Ductile iron ASTM A536 (65-45-12 / 80-55-06) or EN-GJS-450-10 |
| Rated Load | 8,000–15,000 lbs (36–67 kN) per connection point, per drawing |
| Hook Opening | Sized for 3/8"–1/2" EHS strand or matching thimble |
| Eye Diameter | 1-1/4"–1-3/4" (32–44 mm) inside diameter |
| Hole Diameter & Spacing | 11/16"–13/16" (17.5–20.6 mm) bolt holes; 1-1/2"–3" spacing per drawing |
| Bolt Size | 5/8" (16 mm) or 3/4" (19 mm) machine bolts |
| Finish | Hot-dip galvanized per ASTM A153 |
| Suitable Guy Wire Size | 3/8", 7/16" or 1/2" EHS guy strand |
| Weight Range | 1.0–3.2 kg per piece |
| Casting Process | Green sand casting, hook and eye profiles machined as required |
The combination attachment bolts to the pole face with a single 5/8" machine bolt on wood poles (two-bolt patterns available for concrete poles or heavier loads). The hook is oriented along the primary guy lead, and the eye can accept a secondary lead, a hot-line link, or a thimble clevis at a different angle—line crews often use this to consolidate the attachment zone when a pole already carries transformers, arresters, or communication hardware. Because hook and eye are one casting, there is no risk of the two hardware pieces rotating out of relative position, which simplifies tensioning: set the primary guy in the hook, then connect the secondary lead to the eye without repositioning hardware.
This fitting is a good match for angle poles, dead-ends with auxiliary leads, and reconstruction projects where existing bolt holes must be reused—the combination body often covers two old attachment positions with one new fitting. Where the secondary connection is a clevis-ended assembly rather than a looped strand, specify the lower bolt clevis hole variant.
We cast this fitting from your drawing or sample in our own pattern shop. Typical modifications include: hook opening matched to a specific strand or thimble; eye diameter matched to a ball clevis or hot-line link pin; two-bolt mounting for concrete pole inserts; and section thickening for higher rated loads. Reverse-engineering of legacy combination fittings is routine—send the sample and we return a dimensioned drawing for approval before tooling. Sample lead time is typically 2–4 weeks, with material certificates included.
Each lot is controlled through: dimensional inspection against the approved drawing; mechanical testing of companion cast bars (tensile, yield, elongation per ASTM A536); hot-dip galvanizing thickness measurement; and 100% visual inspection, with magnetic particle inspection of the hook root available on request. Export packaging uses cartons on pallets, 25–50 kg per carton, moisture-proofed, with customer labels and packing lists.
1. What is the difference between this fitting and the lower bolt clevis hole variant?
This standard version carries the secondary connection as an open eye; the lower bolt variant provides a machined lower bolt hole sized to receive a clevis-ended assembly, changing what can be hung below the main attachment.
2. Can the hook and eye take load simultaneously?
Yes, within the rated load of each connection point; combined loading cases should be reviewed against your pole loading calculation.
3. Is a single-bolt mounting strong enough?
For standard distribution guying on wood poles, yes; for heavier loads or concrete poles we supply two-bolt patterns.
Send your drawing or sample for pricing and lead time within 24 hours. Reach our foundry engineers on WhatsApp: +86 185 6156 7088 — samples and material certificates available.
Need a formal quotation? Send your Combination Guy Hook / Pole Eye Attachment drawing, quantity and target price through our quotation request form — it goes straight to the foundry inbox, and we reply with a priced offer, material certificate draft and production lead time within one business day.