![]()
![]()
An auxiliary eye is a small forged or cast power line hardware fitting that provides an additional attachment eye on an insulator string, crossarm assembly, or guy attachment. Unlike primary load-path links such as the clevis eye or ball eye, the auxiliary eye is designed to carry secondary connections: ground wire leads, jumper loops, pull-off wires, warning flags, or an extra anchor point for a hot-line clamp. Cast in ductile iron and hot-dip galvanized for outdoor service, it is a low-cost component that solves a frequent problem on overhead distribution and substation structures — where to hang the next thing.
On a typical distribution line, linemen attach a surprising number of secondary items to a single structure. Grounding conductors must be secured near the insulator, neutral tails need a tie-off point, and maintenance crews expect a place to hook a block or grip. An auxiliary eye bolted to the yoke plate, clevis, or crossarm bracket gives every one of those items a clean, repeatable anchor, keeping the line tidy and reducing the chance of a loose wire swinging into phase. Because the fitting sits outside the main mechanical path, its strength requirement is typically lower than that of suspension links, but dimensional repeatability still matters: the eye bore must accept standard cotter pins and hardware used across ANSI-style line fittings.
| Item | Typical Value |
|---|---|
| Material | Ductile iron ASTM A536 (65-45-12 typical); malleable iron available on request |
| Strength Rating | Rated holding strength typically 4,000–10,000 lbs class, dependent on bore and section |
| Eye (Hole) Diameter | 11/16" or 13/16" typical, accepting standard line hardware pins |
| Hole Spacing | Bolt-hole center distances per customer drawing, commonly 1-1/2"–3" |
| Finish | Hot-dip galvanized per ASTM A153 |
| Suitable Insulator String | Pin insulator and polymer post assemblies; used as auxiliary attachment on suspension strings |
| Weight Range | Approx. 0.3–1.2 kg per piece |
| Casting Process | Green sand casting, shot-blasted, eye bore machined |
| Standard | Manufactured to ANSI C29-series line hardware conventions |
Installation is deliberately simple. The auxiliary eye is bolted through a matching hole on a yoke plate, pole band, or clevis using a standard machine bolt and cotter-pinned eye connection. From our experience supplying casting foundries and utility distributors, the most common uses are:
Ground wire attachment: securing the down-lead from the pole-top pin insulator to the grounding strap.
Jumper and tail support: holding slack jumper loops clear of the structure on dead-end poles.
Second-point rigging: providing a hang point for pulley blocks, hot-line tools, or signage during stringing and maintenance.
Guy-adjacent accessories: supporting guy markers or spool ties near the guy attachment without loading the strand directly.
Because the eye is cast, the section around the bore is generous compared with a bent-rod eye, which helps the galvanized coating stay intact during installation — a common failure point for bent wire eyes.
We produce auxiliary eyes from customer drawings or samples. Common customizations include enlarged eye bores for oversized hardware, tapped or slotted variants, extended shank lengths, and matching hole patterns for specific yoke plates. Sample lead time is typically 2–3 weeks after drawing confirmation, and first-article inspection reports are available before volume production.
Each production lot undergoes: (1) dimensional checks of eye bore, hole spacing, and thread engagement using go/no-go gauges; (2) hot-dip galvanizing thickness verification with magnetic coating gauges against ASTM A153 minimums; and (3) periodic tensile sampling on a calibrated pull tester to confirm the rated holding strength. Parts are packed in cartons of 25–50 with moisture-barrier lining and palletized for export.
Q: How is an auxiliary eye different from a clevis eye?
A: A clevis eye sits in the main load path of the insulator string and carries the full rated tension. An auxiliary eye is a secondary attachment point for grounds, jumpers, and tools, so its typical strength rating is lower and it is usually bolted to a supporting fitting rather than strung in-line.
Q: Can the eye bore be machined to non-standard sizes?
A: Yes. Bore diameters and hole spacing are machined to customer drawings; 11/16" and 13/16" are the most frequently requested sizes.
Q: What galvanizing standard do you follow?
A: Hot-dip galvanizing per ASTM A153, with coating thickness checked on every lot.
Clevis Eye — the primary in-string link for suspension assemblies
Square Flat Washer — matched hardware for bolted eye installations
Need auxiliary eyes matched to your existing insulator string hardware? Send us your drawing or a sample photo, and our engineers will return a casting quote within one business day.
WhatsApp: +86 185 6156 7088 — or request a quote directly through the product inquiry form.
Need a formal quotation? Send your Ductile Iron Auxiliary Eye for Overhead Line Hardware drawing, quantity and target price through our request for quotation form — it goes straight to the foundry inbox, and we reply with a priced offer, material certificate draft and production lead time within one business day.