GGG-40 is EN-GJS-400-15. True at 30 mm wall thickness. At 90 mm the European grade only has to reach 370 MPa and 11 percent elongation, and the German name stops being a promise.
ASTM A536 65-45-12 has no European equivalent at all. Its 448 MPa tensile, 310 MPa yield and 12 percent elongation sit between EN-GJS-450-10 and EN-GJS-400-15, and at no thickness band does either of them match all three numbers.
A grade table buys you a shortlist. Approval takes four more checks: wall thickness band, sample type, specimen geometry, and the supplementary requirements that never reached the purchase order.
A536 prints three minimums in the name. EN 1563 prints two and hides the yield in a table. That asymmetry is where most substitution errors begin.
| System | Example | What the digits mean | Where the rule lives |
|---|---|---|---|
| ASTM A536 | 65-45-12 | 65 ksi tensile, 45 ksi yield, 12 percent elongation | Grade name; inch-pound values govern, metric is informative |
| EN 1563 | EN-GJS-400-15 | 400 MPa tensile, 15 percent elongation | Yield and proof strength come from the property tables |
| DIN 1693, legacy | GGG-40 | 400 MPa tensile, material number 0.7040 | Superseded; decimal suffix carries extra requirements |
| GB/T 1348 | QT400-15 | 400 MPa tensile, 15 percent elongation | Chinese national standard |
| JIS G 5502 | FCD400-15 | 400 MPa tensile, 15 percent elongation | Japanese industrial standard |
| ГОСТ 7293-85 | ВЧ40 | 400 MPa tensile level | Yield, elongation and impact sit in separate clauses |
Read a name like 65-45-12 and you know the tensile, the yield and the ductility without opening anything. Read EN-GJS-500-7 and you know two of the three; the 320 MPa proof strength is in Table 1 of the standard, not in the designation. Two names that look parallel are not carrying the same set of facts, and that alone causes substitutions that pass on paper and fail in inspection.
The DIN decimal suffix is the other trap. GGG-40 and GGG-40.3 are not the same material. The .3 variant adds an impact requirement at low temperature, and dropping the suffix to tidy up an old drawing deletes a test the designer paid for.
These rows align grade families for screening. They do not authorize a swap.
| EN 1563 | DIN 1693 | GB/T 1348 | JIS G 5502 | ГОСТ 7293-85 |
|---|---|---|---|---|
| EN-GJS-400-15 | GGG-40 | QT400-15 | FCD400-15 | ВЧ40 |
| EN-GJS-450-10 | GGG-45 | QT450-10 | FCD450-10 | ВЧ45 |
| EN-GJS-500-7 | GGG-50 | QT500-7 | FCD500-7 | ВЧ50 |
| EN-GJS-600-3 | GGG-60 | QT600-3 | FCD600-3 | ВЧ60 |
| EN-GJS-700-2 | GGG-70 | QT700-2 | FCD700-2 | ВЧ70 |
| EN-GJS-800-2 | GGG-80 | QT800-2 | FCD800-2 | ВЧ80 |
The GGG-45 row appears in the table because DIN 1693 lists that grade at 450 MPa tensile, 310 MPa proof and 10 percent elongation. Several published cross-reference charts skip it and label the 450-10 row "no German equivalent", which sends European buyers looking for a grade that has existed for fifty years.
ASTM is absent from this table on purpose. Putting 65-45-12 in the 450-10 row would imply a match that the numbers do not support, and putting 60-40-18 in the 400-15 row would hide a 26 MPa gap in yield. The ASTM comparison gets its own table below, where the gaps are visible.
EN 1563 does not give one set of minimums per grade. It gives three, and they depend on how thick the casting is at the section that matters.
All values are minimums, tensile and proof in MPa, elongation in percent. A dash means that standard does not band the grade by thickness.
| Grade | t ≤ 30 mm | 30 < t ≤ 60 mm | 60 < t ≤ 200 mm |
|---|---|---|---|
| ASTM A536 65-45-12 | 448 / 310 / 12 | — | — |
| EN-GJS-400-15 | 400 / 250 / 15 | 390 / 250 / 14 | 370 / 240 / 11 |
| EN-GJS-400-18 | 400 / 250 / 18 | 390 / 250 / 15 | 370 / 240 / 12 |
| EN-GJS-500-7 | 500 / 320 / 7 | 450 / 300 / 7 | 420 / 290 / 5 |
| EN-GJS-600-3 | 600 / 370 / 3 | 600 / 360 / 2 | 550 / 340 / 1 |
A536 does not publish a thickness series of this kind. Its minimums are established on separately cast test coupons, and the standard does not promise the same figures in a heavy section. That is not a defect in the American system; it is a different convention with a different sampling basis, and it is the reason the two columns cannot be subtracted from each other without knowing the band.
Now read the first two rows together. Up to 30 mm, 400-15 gives you three extra points of elongation and takes away 48 MPa of tensile and 60 MPa of proof. A designer choosing between them at that thickness is trading strength for ductility, and either choice is defensible.
Past 60 mm the trade disappears. 400-15 owes 370 / 240 / 11 against 448 / 310 / 12, which is 78 MPa lower in tensile, 70 MPa lower in proof and one point lower in elongation. A European grade is not a stronger version of the American one at that thickness; it is a weaker one on every axis.
That single fact reverses the direction of a substitution. Replacing an A536 65-45-12 requirement with GGG-40 on a thick part loses strength. Replacing a GGG-40 requirement with 65-45-12 gains it, and the part passes both. Equivalence is not symmetric, and most substitution forms are written as if it were.
The asymmetry shows up one level up as well, between material families. Whether the part should be ductile iron at all is a question about the carbon line, not about grade suffixes, and it is covered separately in cast iron against cast steel.
EN 1563 clause 5 requires the buyer to state the relevant wall thickness when ordering. Almost no enquiry does.
When the thickness is missing, the supplier picks the band that suits production, the inspector measures against the band that is printed first in most summaries, and the batch fails on a requirement that was never priced. We have watched that argument run for three weeks on a housing whose only fault was a drawing that never named a band.
Clause 7.1 adds a second detail worth knowing: the material designation is based on properties from cast samples 25 mm thick, and the designation does not change with the type of sample. So the grade name tells you the family and the strength level. It tells you nothing about how that level will be demonstrated.
Above 200 mm the standard stops answering. Clause 7.1 leaves the minimum values, the sample type and the sample size to agreement between foundry and purchaser, so a 300 mm section has no published floor for a buyer to quote against. Whoever writes that agreement first sets the acceptance criteria.
Gray iron runs on the same logic. EN 1561 sets GJL grades across four thickness bands, from 20–40 mm up to 150–300 mm, and the guaranteed tensile falls as the section gets heavier. Compare gray iron and ductile iron by grade name alone and the same error repeats one family over.
A C after the designation means the test pieces come out of the casting rather than from a separate mould, and the minimums fall with them. Across the full range the drop is 50 MPa of tensile and seven points of elongation.
| EN-GJS-400-15, cast sample | t ≤ 30 | 30 < t ≤ 60 | 60 < t ≤ 200 |
|---|---|---|---|
| Cast separately or cast-on | 400 / 250 / 15 | 390 / 250 / 14 | 370 / 240 / 11 |
| Cut from the casting, suffix C | 390 / 250 / 12 | 370 / 240 / 11 | 350 / 230 / 8 |
Take a 90 mm flange on a cast iron pump housing, drawing marked EN-GJS-400-15, no sampling note. The band is 60 < t ≤ 200, so the minimum is 370 / 240 / 11. If the customer's inspector cuts a coupon out of the flange wall, the applicable row is 350 / 230 / 8 — 20 MPa below the cast-sample row for the same band, and three points below on elongation.
We settle this before tooling, not after the first article. When a drawing carries a C or a note about testing at a stated location, we ask for written confirmation of the sample position, because a separately cast coupon will never prove a property inside the casting.
The practical rule: a drawing that says EN-GJS-400-15 and nothing else is under-specified. A drawing that says EN-GJS-400-15C is specifying something considerably softer than 400 MPa.
ASTM A536 uses a 0.5 in diameter specimen with a 2 in gauge length, a ratio of four diameters. ISO and EN use a 10 mm diameter specimen with a 50 mm gauge length, a ratio of five. GB/T 1348 follows the ISO proportional specimen.
Both gauges are close to 50 mm, so the numbers are broadly comparable, but not identical. A 12 percent result on a 4D specimen and an 11 percent result on a 5D specimen are not one point apart in material behaviour; part of that difference lives in the test method.
This matters at the margin, which is exactly where ductile iron grades cluster. 400-15 against 65-45-12 differs by three points of elongation at thin sections and one point at thick ones. Anyone comparing those figures across standards without noting the specimen is measuring the method as much as the metal.
We pour EN-GJS-400-15, 450-10, 500-7 and 600-3 on the clay sand line, and the same families in ductile iron pipe fittings and pole line hardware where A536 65-45-12 is the usual callout.
When a European drawing arrives with GGG-40 and a section over 60 mm, we quote it against the 60 < t ≤ 200 band and put those three numbers on the quotation: 370 / 240 / 11. Buyers sometimes read that as us quoting a lower grade. It is the same grade, at their thickness, and writing it down early is cheaper than arguing about a test report in month four.
Two things we will not do quietly. We do not issue routine dual certification against A536 and EN 1563 from one heat, because the two systems want different coupons and the arrangement has to be agreed before pouring. And when a drawing requires properties at a stated location inside the casting, we ask for that in writing before pattern work starts. Both change the price, and both are cheaper to discuss at quotation than at first article.
The certificates we issue carry the heat number, spectro chemistry, tensile results and nodularity, and third-party witness can be arranged when the order asks for it.
Is GGG-40 the same as A536 65-45-12?
No. GGG-40 maps to EN-GJS-400-15, which owes 400 MPa tensile and 15 percent elongation at thin sections. A536 65-45-12 owes 448 MPa and 12 percent. They differ in both directions, and the gap widens past 60 mm.
What is the ASTM equivalent of GGG-40?
The nearest A536 grade is 60-40-18, at 414 MPa tensile and 18 percent elongation. It is a candidate for review, not a substitution, because the elongation requirement is three points higher than the European grade.
Can EN-GJS-400-15 be supplied with impact testing?
Only when it is ordered. The base grade carries no impact requirement. Low-temperature impact sits on separate designations, EN-GJS-400-18-LT and its relatives, and the test temperature has to be stated.
Why does an old drawing say GGG-40.3?
The decimal suffix marks the variant with a guaranteed impact value at low temperature. Replacing it with GGG-40 removes that guarantee, which is a design change rather than a simplification.
Does EN 1563 require the wall thickness to be stated?
Yes. Clause 5 lists the relevant wall thickness among the details the purchaser must supply, alongside the standard number and any special requirements.
Send the drawing revision, the full grade designation with any suffix, the section thickness at the loaded area, and the acceptance basis — separately cast coupon, cast-on sample, or coupon cut from the casting. Four lines.
With those four, a quotation can state the exact minimums the part will be judged against. Without them, every supplier is guessing at a different band, and the cheapest quote is usually the one that guessed lowest.